Mold Release Agents
For use in all industries. Contact
us for more information.
A Better Way to
Spray Release Agents and Sealing Agents: The New Kwikee(TM) Sprayer System
Smooth-On
sells thousands of cans of aerosol release agent every year. Some
customers have purchased 50 or 60 cases of release agent for a single
project, unaware that these release agents are available in liquid or
“bulk” form.
While convenient, aerosols are an
inefficient and expensive way to deliver release agent compared to
brushing on or spraying on liquid releases. We are introducing the
Kwikee(TM) sprayer as an economical alternative to aerosols. It is a
faster, labor-saving way to cover large models or molds and delivers
sealing agent or release agent in a fine mist.
For large projects, the Kwikee(TM)
eliminates the problem of aerosol plume in the air. For the average
“small-time” mold maker/caster, aerosols will still represent the best
value. For production settings, the cost of the Kwikee(TM) sprayer will pay
for itself after a single use in terms of material cost and labor
savings you’ll experience using liquid release agents vs. aerosols.
Make sure you observe all safety
precautions when using the Kwikee, especially when spraying flammable
sealers and release agents.
Rubber & Plastic Mold Release Agents
|
Polyurethane Elastomer Casting |
| ER 200 |
Model and pattern release
for mold making epoxy, urethane and RTV silicone molds. |
| ER 500 |
Paintable release for all
elastomers and foams. Produces flat finish. |
| ER 2831 |
Wax based
release agent for urethane elastomers and foam. Temperature Range:
150-230 F (65-110 C) Room temperature release agent-sealer on plastic
molds. |
| AQ
75 |
New silicone
concentrate for polyurethane elastomer molding. Dilution ratio with better release
and reduced build-up. |
| AQ
50 |
Ready to use version of
Aqualease 75. |
|
Polyurethane Foam |
| ER 1700 |
Paintable
release agent for rigid urethane foam. |
| ER 2770 |
Wax based
release for polyurethane flexible foam. Temperature Range: 110-130
degrees F
(43-55 degrees C) |
| ER 2831 |
Wax based
release for urethane elastomers and foam. Temperature Range:
150 - 230 degrees F
(65 - 110 degrees C). Room temperature release agent-sealer on
plastic molds. |
|
Rubber Molding |
| In & Out(TM) II |
Water-soluble–-an
improvement in everyway over our original In & Out water based release
agent. Reports from customers who have switched suggest that In & Out(TM) II
offers the following advantages over original In & Out(TM):
• better release from rubber molds,
• non-staining,
• does not cause molds to swell or shrink
• reduces build-up in molds and leaves molds cleaner,
• multiple release from one application. |
| ER 400 |
Superior release for
rubber molds. Not paintable |
| PL 3440 |
FLOWCOAT heat
flowed coating for fluoroelastomer rubber. |
| AQ 75 |
New silicone
concentrate for polyurethane elastomer molding. Dilution ratio with
better release and reduced build-up. |
| AQ 50 |
Aqueous
silicone release agent. Ready to use version of AQ-75 |
Polyester
Lay-up & Casting |
| PL SMG |
Mold prep
coating to seal micro-porosity and to protect surface from styrene attack. |
| PL 600 |
Semi-permanent
release coating for gel-coat FRP processing. Wipe-on, wipe-off. |
| ER 2125
PVA |
PVA release
coating for polyester FRP lay-up. Available in green or clear. |
Thermoplastic
Molding |
| ER 800 |
Release agent
for thermoplastic molding and making addition and condensation cured RTV
silicone rubber molds. Produces flat finish. |
| ER 1700 |
Paintable
release agent for thermoplastic molding. |
Silicone
RTV |
| ER 200 |
Model
and pattern release
for making epoxy, urethane and platinum cured silicone molds. Produces
satin finish. |
| ER 800 |
Release agent
for making addition and condensation cured RTV silicone
molds. |
| ER 500 |
PTFE
paintable release for molding silicone RTV. Produces flat finish |
